Improvised Survival Life Vest

Your pants can be used for more things than just holding your wallet and keys. Your pants can actually help save your life in a water survival scenario.

Lets use a scenario where you are out boating several miles from shore and for some unforeseeable reason the boat sinks. The boat owner did not have life jackets or any other flotation devices on board. Hopefully, you are not the boat owner that made that costly mistake.

Now, the boat is nowhere in sight because it is now at the bottom of the lake. You are alone and hopefully have some type of swimming skills, especially on how to tread water. If you can not swim, I would suggest learning now before you need the ability to do so. If you can't swim or tread water, this technique will not work for you.

If you are wearing shoes, attempt to remove at least one show string and discard your shoes. This will remove some wait that will drag you down. Hold the shoe string in your mouth until needed for the next steps. If you are able to tie the bottom of the pant legs together into a knot, then you may not need the shoe strings. It depends on how thick your pant material is and the pant size. The larger the pants, the more difficult to tie. I know from experience. 

Remove your belt if you have one. Remove any heavy objects from the pockets like keys, etc.

While doing these steps, it is important not to panic. You may need to go under water once in awhile to do some of these steps to relieve some pressure from treading water. Just hold your breath, sink a little, do a step, and then come back up for air. The colder the water, the harder it is to do these steps.

After removing the belt and other items, if you are able to slip your pants off without undoing the snap and zipper then do so. If not, you will have to close the snap and zipper after removing your pants.

Once the pants are off and everything is snapped up, you will need to tie the pant legs together at the cuff so that air will not escape through them. If you are able to tie the legs together into a knot without using the string, then do that. If it is difficult, then use the shoe string. I prefer to use the shoe string because I can tie the pant leg opening closer to the ends so that it will hold more air.

Next, will need to place your head between the opening of the pant legs with the cuff facing to your back and the zipper facing down into the water. You should be looking at your rear pant pockets if done correctly. 

Next, bring the opening up above your head and the scoop downward toward the water trapping air into the pant legs. You need to squeeze the belt opening together at chest level so that air does not escape back out. You will need to do this step as needed to keep air in the legs. You can also slightly open the belt area up and slap water and air into the opening and then close it back up.

Next, after the pant legs are puffed up with air, lean back slightly while keeping the belt opening closed at the chest with your arms. Determine where the nearest landfall is and start pedaling with your feet toward that direction. You will be traveling backwards, so every now and then look back to make sure your are not heading for any type of hazard or danger.

There is an alteration to this technique. You can tie off each pant leg individually resulting in two floating ends. You keep the belt opening down into the water and place your chest between the crotch area and you can pedal forward on your chest rather than on your back.

Note:  If your pants have holes in the knees or crotch area, this technique will not work.

Stay Prepared! Stay Alive!

Charlie

Cotton Ball Friction Fire

Items needed:

100% cotton balls
Wood ash (the white part of the burnt fire)
Two wood boards (2 x 4, 1 x 4 etc.)
Tender bundle

Prepare the cotton ball by opening it up and form it into square shape. Put about a teaspoon of wood ash on top of the bottom 1/3 of the cotton strip. 

Starting from the bottom, roll the cotton ball as tight as you can get it. Next, roll the cotton cylinder on the board with the palm of your hand to make it tighter. Then, using one of the flat boards, roll it again to make it even tighter.

Next, using the same board, begin rolling the cotton cylinder back and forth in a sawing motion, pressing down with firm pressure. After about 12-15 strokes, lift the board and check for embers. If you see smoke, you make have to open the center of the cylinder a little, to let in some oxygen.

If it has not started to smoke or catch and ember, continue to with the sawing motion until an ember or smoke is produced. If the material is spent and has not produced smoke, you may need to make another bundle and start again. Add a little more of the ash on the second attempt.

Once you have obtained an ember, transfer it to the tender bundle and complete your fire making steps.

Other materials can be used to produce the same effects. Cotton cloth strips, paper towels, dried yucca fibers can be substituted for the cotton balls. Rust from metal can be used in place of the wood ash.

A flat rock can used as a base instead of wood.

Stay prepared! Stay Alive!

Charlie

Field Kit For Expedient Reloading Of Shotgun Ammo

Warning: For educational purposes only. Use these techniques at your own risk.

Tools used for field expedient reload

Correct primer surfacing

Tools/Equipment:

1. Brass shot shells (size for weapon system being used, 12 gauge, etc.)
2. Shot
3. Pyrodex Rifle and shotgun powder (or preferred brand)
4. 209 shotgun primers
5. Large pistol primers
6. Wadding material
7. Over shot card material
8. Lighter and glue stick
9. Primer crimp tool or "C" clamp setup with deep well socket
10. Primer removal tool
11. Powder tamper tool
12. Powder and shot measuring tool
13. Container for brass shells
14. Container to store kit
15. 15/64 inch drill bit
16. 23/64 inch drill bit
17. Wad and over shot cutter tool
18. Drill
19. Flat piece metal stock
20. Rubber hammer or similar 
21. Flat piece of wood stock

Converting brass shell to accept the 209 primer:

1. First use the 15/64 drill bit and drill out the primer hole.
2. Using a 23/64 drill bit, drill a slight recess in the primer hole deep enough to allow the primer rim to seat flush with the bottom of the shell. See photo above.
3. Seat the 209 primer like you would a regular 12 gauge shell when reloading.

Note: Shotgun firing these types of reloads need to be cleaned more often than factory loaded ammo.

Reload 209 Primers Using Field Expedient Methods

Warning: For educational purposes only. Use these techniques at your own risk.

Tools used for field loading

Items Needed To Reload Primer

Set up to separate 209 primer components

209 Primer separated

Suggested tools used:

1. Antique hand primer crimp tool
2. Wood dowel for powder, wad and shot compressing
3. Primer removal tool with socket base (5/8 inch socket)
4. Rubber hammer
5. Wad cutter tool (for what ever size shell you are loading)
6. Flat punch that fits inside primer cup to flatten out dimple
7. Flat piece of metal stock
8. Flat piece of wood
9. Strike anywhere matches
10. Powder and shot measuring cups
11. Wad material (paper, plastic, wool, etc)
12. Over shot card material (cardboard, playing cards, etc)
13. 5.5 mm socket (used to remove primer cup)
14. Pin or finishing nail used to pound out primer cup.
15. Lighter or similar flame source
16. Glue stick
17. Rifle and shotgun powder with container (I used Pyrodex RS)
18. Bird shot with container (I used #7 1/2 in the video)


Note: Do not allow the ammo to get wet. Do not jar the ammo around by throwing into an ammo can or something of that nature. Protect the ammo until it is needed. It is best to shoot this ammo from a single shot or double barrel shotgun rather than a pump action. A pump action can be used if you load and fire one round at a time rather than using the pump action.

One drawback from reloading spent primers is the chance that the match head powder or what ever other ignition source was used may not ignite and you get a dude fire.

In the event the primer does not ignite, wait about 60 seconds with the end of the barrel pointed on target in the event there is a cook off. A cook off is when the powder could be smoldering but has not yet ignited. If it ignites and the end of the barrel is pointed toward someone, there may be a chance of an accidental shooting.

Always inspect the shells for damage and cracks. Do not reuse or shoot damaged ammo. Use safety glasses when loading your ammo and keep open flames away from your powder. 

Stay Prepared! Stay Alive!

Charlie

Field Expedient Ammo Reloading

Caution: This lesson is for educational purposes only. Gun powder is dangerous. Firing damaged or incorrectly loaded ammo is dangerous as well. 

PRIMER CRIMPER

WAD CUTTER

There may be a time in ones life when it may become necessary to have to reload ammo in the field, especially in a wilderness survival situation or the collapse of society. 

We are comfortable in knowing that at the moment we have access to ready made store bought ammo. But, what if that luxury was some how taken away? What if there were no stores left or available to purchase our ammo?

In such as situation, ammo can still be available if one knew how to obtain what was needed to reload their own. Spent ammo shells, especially shotgun shells can be found laying around all over the desert. Primers can be reconditioned and reloaded. Black powder can be homemade. Lead shot can be made from scrape lead.

You really do not need fancy reloading equipment in order to reload ammo in an emergency or self reliant situation.

Learn now to start saving your spent ammo hulls and shells. Set them aside to be reloaded at a later date when the time is needed.

Here are the steps that were covered in the video to reload a 12 gauge shell: (if this is the first time a plastic shotgun shell is being used, cut the top crimp fingers off the shell where the crimp line meets the star crimp.)

1. Remove primer
2. Install a new primer
3. Measure powder and add to shell
4. Using dowel rod, gently compress the powder in the shell
5. Add correct amount of wading (plastic, paper, animal hair, leather, etc.)
6. Using dowel rod again, gently compress the wad into the shell
7. Add correct amount of shot. (insure that there is enough room at the opening of the shell to add the over-shot card)
8. Add over-shot card and compress gently with dowel rod
9. Add glue over top of shot card ensuring that the inside walls of the shell receive glue as well
10. Immediately add another shot card over the top of the first one and apply gentle pressure to allow glue to spread out

Note: Do not allow the ammo to get wet. Do not jar the ammo around by throwing into an ammo can or something of that nature. Protect the ammo until it is needed. It is best to shoot this ammo from a single shot or double barrel shotgun rather than a pump action. A pump action can be used if you load and fire one round at a time rather than using the pump action.

Always inspect the shells for damage and cracks. Do not reuse or shoot damaged ammo. Use safety glasses when loading your ammo and keep open flames away from your powder. 

Stay Prepared! Stay Alive!

Charlie